MSI Z170A GAMING PRO CARBON have 7 PCIE-E slots,it's a good motherboard to build mining rig.
Old BIOS is hard to MOD and only can run 6 GPU at same time.
How to use old BIOS MOD to success 6 GPU see my blog old past (
link)
2016-12-26 MSI release new BIOS version 1.7 for Z170 and Z170A motherboard
It's easy to setting and successful mining 7 GPU at same time.
My mining rig:
(1)CPU : Intel® Celeron® Processor G3900
(2)Motherboard : MSI Z170A GAMING PRO CARBON
(3)GPU : MSI GAMING X RX 470 4GB * 6 and MSI GAMING X RX 470 8GB * 1
(4)Memory : Kingston 8GB DDR4 2400
(5)SSD: 120GB
(6)PSU : CORSAIR RM1000X
(7)Other : USB 3.0 PCI-E Express 1x To 16x Extender Riser Card Adapter X6
(8)System : Windows 10
Step 1. Download BIOS Version 1.7
Step 2. Unzip and put BIOS file E7A12IMS.170 to USB flash disk root directory.
Step 3.
Shutdown computer and don't plug in anything on PCI-E slots.
Only plug in HDMI cable and BIOS USB flash disk.
Step 4. Boot up and into BIOS and press F7 to Advanced.
Step 5. SELECT M-FLASH
Step 6. Press Yes to Auto reboot enter flash mode.
Step 7. M-Flash mode
Step 8. Select BIOS file E7A12IMS.170 and press YES to flash BIOS.
Step 9. Waitting BIOS Updating
Step 10. Into BIOS
Settings>Advanced>PCI subsystem Setting
PEG 0 and PEG 1 set to Gen1
Above 4G Decoding set to Enabled
Step 11.
Settings>Advanced>Integrated Peripherals
Unchanged
Step 12.
Settings>Advanced>Integrated Graphics Configuration
Unchanged
Step 13.
Save change BIOS and shutdown computer.
Plug In all USB extender riser and HDMI cable plug In Graphics card.
Step 14. Boot up into Win 10 the 7 GPU is get.
Step 15. ETH mining Claymore can detect 7 GPU.
Step 16.
MSI GAMING X RX 470 4GB *6 +
MSI GAMING X RX 470 4GB *1 = 195 Mh/s ETH
Step 17. This is my 7 GPU mining rig
Step 18. This is easy to build 7 GPU mining rig.
Tuning GPU see my blog:
How to distinguish GPU quality to tuning your GPURX 470 4GB BIOS MOD see my blog:
MSI GAMING X RX 470 4GB BIOS MOD Hynix chip 28 Mh/sRX 470 8GB BIOS MOD see my blog:
MSI GAMING X RX 470 8GB BIOS MOD Micron chip 28 Mh/sHope it helps you.
Comments
But only thing is…..your windows 10 installation should be in uefi or it should support uefi in bios not legacy……windows hardrive should be in gpt format…..other wise the above 4g setting won’t work and u will get a black screen when u try to boot in to windows 10…….I used 16.9.1 driver for my amd Rx 480 nitro+oc cards
My setup is
MSI z170a gaming pro carbon motherboard
Rx 480 8gb nitro+oc graphics cards
Usb powered risers 1x to 16x for graphics card
I5 processor(a cheap one)
Ram Kingston hyper fx 16 GB 8×2
Kingston 120 GB SSD
Thermal take 1200 watt power supply
any one upgarde it?
my configuration:
i5 6600k
MSI GAMING Z170A PRO CARBON
Corsair 16 GB DDR4
Intel 80GB SSD
4x RX 480 Nitro + 8gb
1x R9 390 Nitro 8gb
5x Riser 1x to 16x
Corsair 1200w
I have this problem:
I followed the tutorial ...
if the active Above 4G Decoding = Boot and then hangs (ssd stops blinking, screen on and black, no image)
if not active Above 4G Decoding = Boot Windows and complete, but only two RX 480 work, the others are in conflict
What should I do?
Ok ...
Yesterday:
copied and flashed new BIOS of this page
Then I beat my head against all the walls of the house
I describe what I did this morning ...
1) reset Bios
2) I downloaded in the laptop with Windows 10 .IMG Media Creation Tool Pro ... Windows (in my case Italian) x64 only
3) with rufus 2.6 as explained in this videoo ( I prepared USB support
4) Connected USB key, keyboard + mouse, Intel 80GB SSD to the motherboard, but without video cards (graphics cards with 3 long beeps and a blank screen)
5) He entered the Bios:
-del or F1 depends on the case
-F7
-Settings / Advanced
--- PEG = 0 "Gen 1"
--- PEG = 1 "Gen 1"
--- PCI Latency = "32 (default)"
--- Above-4G "Enabled"
-Settings / Integrated Peripherals
--- On Board Lan = "Enabled"
--- Sata Mode = "AHCI"
--- Audio = "Enabled"
--- HPET = "Enabled"
--- everything else "Disabled"
-Settings / Integrated Graphics
--- Initiate Graphic = "PEG"
--- Shared Memory = "64"
--- IGD = "Disabled"
-Settings / USB Configuration
--- All = "Enabled"
-Settings / Windows OS Configuration
--- Windows 8.1 / 10 = "Enabled
--- Windows 7 = "Disabled"
--- MSI Fast Boot = "Disabled"
--- Fast Boot = "Enabled"
---> = Secure Boot Secure Boot Support = "Disabled"
---> = Secure Boot Secure Boot Mode = "Standard"
-Settings / Boot
--- Boot Mode Select = "UEFI" (now you can not change)
--- Boot Option # 1 = "UEFI USB KEY"
--- Boot Option # 2 = "UEFI Hard Drive"
-Settings / Save & Exit
---> Save Changes and Reboot
Now Part Installing Window 10
Just load the language selection screen, press Shift + F10
It opens a CMD window
write:
"Disk part"
"List disk"
"Select disk x" (x = is the disk on which you install)
"Clean"
"Exit"
close CMD and continue installation of Windows 10
Now Windows is installed but no video cards !!!
Install all Drivers Motherboard
Now I enter 1 or all Riser cards (4x RX 480 Nitro + 8gb and 1x R9 380 Nitro 8gb) and ... 1 long + 2 short beeps, black screen, but I think that windows works.
I do not understand where I'm wrong Huh
A few days ago I changed the firmware of Sapphire RX 480 Nitro + 8gb,
to do so I moved the switch to the side of the connections ...
by chance I came to my mind and I put affixed to it and ...
IT WORKS, IS ALIVE, I CREATED A MONSTER
Now I'll have to redo the firmware of the cards and try Claymores
Thank you all
4 x Sapphire RX 480 Nitro + 8gb
1 x Sapphire R9 390 Nitro 8gb
But I have not changed the vbios the RX 480 ...
At first I found and installed the V4 VBios in my 4 Sapphire Rx 480 Nitro + 8gb on Asus Z170 Deluxe, but then I tried to add the R9 390 Nitro 8gb I had in the drawer and Asus does not work with more than 4 cards ...
I ordered a MSI Gaming Z170A Carbon Pro that came yesterday and I immediately changed the BIOS with a lot of problems ... but this is the past ...
Now the V4 worked well before UEFI on my old Windows 10, but now I'm not working the motherboard, I have to use it Stock
vbios version of the RX 480 Nitro + Sapphire is:
Standard
P/N 113-2E3470U.X5W
E347 Polaris 10 XT A1 GDDR5 256Mx32 8GB 300e/300m
Image Size 0xE600
CRC 0x4100
Silent
P/N 113-2E3470U.S5W
E347 Polaris 10 XT A1 GDDR5 256Mx32 8GB 300e/300m
Image Size 0x80000
CRC 0x4700
I tried to replace the original Silent and PC works smoothly
I tried to download "Polaris" and edit the original following the parameters of the V4, but the motherboard is one long beep and two short beeps and proceed with the Windows startup, and turned black screen.
Can someone explain me how to do or where to go to find help to vbios that works with UEFI?!?!
Problem solved...
I changed these settings in the Bios:
by so
-Settings / Windows OS Configuration
--- Windows 8.1 / 10 = "Enabled
--- Windows 7 = "Disabled"
--- MSI Fast Boot = "Disabled"
--- Fast Boot = "Enabled"
---> = Secure Boot Secure Boot Support = "Disabled"
---> = Secure Boot Secure Boot Mode = "Standard"
to so
-Settings / Windows OS Configuration
--- Windows 8.1 / 10 = "Disabled"
--- Windows 7 = "Disabled"
--- MSI Fast Boot = "Disabled"
--- Fast Boot = "Disabled"
is...
IT WORKS!!!
I want to remove the R9 390 Nitro 8gbe and add 3 x RX 480 Nitro + 8gb
with this configuration I have a consumption 940W at Wall with 150Mh/s
after the change should be to 1000 / 1050W with 200/210 Mh/s
I think
the board must store the certificates windows components addresses
After verifying the settings in the BIOS were correct with a buddy and it still not working I decided to Disable the ABOVE 4G and booting up to just one video card plugged into Riser in slot 1. After it booted it found the correct video drive and everything looked good. Of course to read all the cards you need to have the Above 4G enabled. I then shut down the computer and re-enabled the ABOVE 4G and it booted up just fine with the one card. I then shut down the computer and plugged in all Risers with Success.
My settings are:
-Settings / Advanced
--- PEG = 0 "Gen 1"
--- PEG = 1 "Gen 1"
--- PCI Latency = "32 (default)"
--- Above-4G "Enabled"
-Settings / Windows OS Configuration
--- Windows 8.1 / 10 = "Disabled"
--- Windows 7 = "Enabled"
--- MSI Fast Boot = "Disabled"
--- Fast Boot = "Enabled"
Im on the OS : ETHOS
I can boot and mine with 4GPU's with the default BIOS settings but not with 6.
When i enter the bios settings above I get a grey screen, (ETHOS wont boot)
Any suggestions or is it getting windows 10 that is the best?
Some keys steps.
a. Have just one card on the motherboard and plug hdmi/other into graphics card.
b. Flash to bios 1.7
b. BIOS Change - PCI Subsystem settings PEGO0 & PEGO1 to Gen 1
c. BIOS Change - Ennure the bios is in UEFI mode check in BIOS under settings/biod and Boot mode select should say 'UEFI'
d. Install MS Windows
e. Check you are indeed running in UEFI mode. Open the System Information Utility (Win Key + "R" > "msinfo32" > OK). In system summary, look for "BIOS MODE".
f. Check you can see all your cards in device manager and they will not be working yet.
g. Install AMD driver and this will take some time and not all the cards will work.
h. Reboot and enter bios.
i. BIOS Change - PCI Subsystem settings - Above 4G Decoding - Enabled
j. When you reboot all the cards should be working.
k. Also remember to changes MS Windows - Advanced system Settings - Performance - set Adjust for best performance otherwise you will drop 2mhs.